Morphometric parameters of the radial neck

TY - JOUR

T1 - Morphometric parameters of the radial neck

T2 - an anatomical study

AU - Koslowsky, T C

AU - Beyer, F

AU - Germund, I

AU - Mader, K

AU - Jergas, M

AU - Koebke, J

PY - 2007/6

Y1 - 2007/6

N2 - INTRODUCTION: The purpose of this study was to describe the anatomy of the intramedullary canal of the radial neck for stem design of radial head prostheses.METHODS: Radial neck measurement was performed from the proximal edge of the radial tuberosity to the distal border of the articular surface on 40 macerated proximal radii using X-rays and Optosil imprints of the intramedullary canal. Radial neck to shaft angle was measured under image intensification.RESULTS: The neck length was 13.3 mm (range 8.0-20.0 mm) measured on X-rays and 13.5 mm (range 9.9-18.8 mm) on Optosil imprints. Concerning the neck's intramedullary canal we obtained a minimum diameter of 9.7 mm (range 6.3-16.4 mm) on X-ray. Corresponding Optosil imprints had a mean diameter of 11.6 mm (range 6.6-18.6 mm) at their proximal end, 10.5 mm (range 5.5-16.3 mm) in the middle and a minimum of 9.8 mm (range 6.0-16.9 mm) at the distal end. Differences between left and right sides were not significant between X-ray and Optosil imprints, nor between left X-ray and right imprints and vice versa at a P-level of 0.001. Radial neck to shaft angle was 167.8 degrees (range 160.5-178 degrees ) measured under image intensification at a rotation angle of 58.6 degrees (range 50-70 degrees ) supination.CONCLUSION: Geometry of the radial neck's intramedullary canal has been described for stem design. The minimum diameter was seen at the distal end, just proximal to the radial tuberosity. A forearm rotation of 58.6 degrees to full supination should be considered during implantation of monopolar prostheses. The wide variety of lengths and diameters complicates standard prosthetic design, but ipsilateral and contralateral X-rays can be useful for preoperative stem size calculation.

AB - INTRODUCTION: The purpose of this study was to describe the anatomy of the intramedullary canal of the radial neck for stem design of radial head prostheses.METHODS: Radial neck measurement was performed from the proximal edge of the radial tuberosity to the distal border of the articular surface on 40 macerated proximal radii using X-rays and Optosil imprints of the intramedullary canal. Radial neck to shaft angle was measured under image intensification.RESULTS: The neck length was 13.3 mm (range 8.0-20.0 mm) measured on X-rays and 13.5 mm (range 9.9-18.8 mm) on Optosil imprints. Concerning the neck's intramedullary canal we obtained a minimum diameter of 9.7 mm (range 6.3-16.4 mm) on X-ray. Corresponding Optosil imprints had a mean diameter of 11.6 mm (range 6.6-18.6 mm) at their proximal end, 10.5 mm (range 5.5-16.3 mm) in the middle and a minimum of 9.8 mm (range 6.0-16.9 mm) at the distal end. Differences between left and right sides were not significant between X-ray and Optosil imprints, nor between left X-ray and right imprints and vice versa at a P-level of 0.001. Radial neck to shaft angle was 167.8 degrees (range 160.5-178 degrees ) measured under image intensification at a rotation angle of 58.6 degrees (range 50-70 degrees ) supination.CONCLUSION: Geometry of the radial neck's intramedullary canal has been described for stem design. The minimum diameter was seen at the distal end, just proximal to the radial tuberosity. A forearm rotation of 58.6 degrees to full supination should be considered during implantation of monopolar prostheses. The wide variety of lengths and diameters complicates standard prosthetic design, but ipsilateral and contralateral X-rays can be useful for preoperative stem size calculation.

KW - Aged

KW - Aged, 80 and over

KW - Female

KW - Humans

KW - Male

KW - Middle Aged

KW - Prosthesis Design

KW - Radiography

KW - Radius

KW - Journal Article

U2 - 10.1007/s00276-007-0206-4

DO - 10.1007/s00276-007-0206-4

M3 - SCORING: Journal article

C2 - 17492250

VL - 29

SP - 279

EP - 284

JO - SURG RADIOL ANAT

JF - SURG RADIOL ANAT

SN - 0930-1038

IS - 4

ER -